auto: the analysts verified the labels of 32 periods (11 stations, up to 14 days each): 710 labels -> 835, 587 unchanged; one analysis folder per period with its report (section Verification)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
df979301b5
commit
2a5d87659b
279 files changed
+10758
-710
No files matched your search
+25
-25
@@ -173,29 +173,29 @@
|
||||
{"id": "WILDSTRUBEL-173", "start": "2026-10-06T08:30Z", "end": "2026-10-06T09:00Z", "family": "Displacement", "description": "PB1_2 alone, on the pavement kerb, goes down at once on corr_x between 08:30 and 08:45 and stays lower in the evening and the next day; its raw position has shifted a little, alone, relative to the set of targets, and its error_value does not change level. On 08/10, it goes down again, with its neighbour PB2_2 (labelled separately). Cause not established (PB1_2 had already been disturbed by something in September): a movement of the kerb is not excluded. To be checked: look at the target PB1_2, keep watching.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-174", "start": "2026-10-06T10:15Z", "end": "2026-10-06T11:15Z", "family": "Obstruction", "description": "A group of passers-by walks along the pavement and the kerb, as blurry trails in front of almost the whole scene (10:45 image): at 10:30, R1 and R2 are set aside, PA3_2 and PB4 rejected, the other targets jump; at 10:45, all the references and all the targets are rejected, the camera is not recalibrated, no curve. Everything comes back at 11:00. The structure is not moving: ignore these two points.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-175", "start": "2026-10-06T14:15Z", "end": "2026-10-06T14:45Z", "family": "Visibility", "description": "At 14:30, the image is very dark (thumbnails of R1, R2 and PB4 almost black): R1 and R2 are set aside, PB4 rejected, and the basis changes for the time of one measurement; PA3_2, PB_5 and PB1_2 jump together, then come back at the next measurement. Cause: a capture that is too dark, not an obstacle. The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-176", "start": "2026-10-06T19:45Z", "end": "2026-10-07T07:00Z", "family": "No data", "description": "No measurement for any sensor during the night, except three isolated measurements at 05:00, 06:00 and 06:30, where several targets are rejected. The station shuts down for lack of energy: just before the outage, the battery is at its lowest and the voltage below its usual night level, and the metrics stop with the measurements; it restarts at sunrise with the solar charge, the compute board still cold (metrics). The curves are missing; nothing moves on the structure, but the station does not have enough energy to last the night: to be checked (battery, panel).", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-177", "start": "2026-10-07T05:00Z", "end": "2026-10-07T12:00Z", "family": "Thermal displacement", "description": "From sunrise until around noon, the camera moves through thermal effect, as every day: its tilt rises (the camera nods down) from 05:00, already a little above its early-afternoon level, to 06:30, markedly above; it goes below this level in late morning (at 11:15) and regains it at 12:00. The pan drops a little at sunrise (at 06:30) then rises a little (at 10:15); the rotation goes markedly above its 05:00 level (at 10:15) and comes back at 12:15-13:15; the scale rises with the temperature (at 07:45) and comes back down from 12:00. In the image, targets and references move together, as a block: y a little positive at 07:15, then a little less negative at 11:15 (ensemble.py --rigide; the targets move away from the block only barely). The housing temperature rises strongly from 04h to 08h and stays hot at 12h: the tilt rises with the warming of the morning and comes back while the housing is still hot; the scale follows the temperature and comes back down with it. The compensation follows: on the corrected curves, the tilt wave weighs on each target only barely more than the noise; what remains is the daytime agitation and the passages (separate labels). Cause given by the expert for this station (label of 27/09): the camera moves through thermal effect, on its lens or its mount; the road does not move with temperature. Normal, nothing to do.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-178", "start": "2026-10-07T05:00Z", "end": "2026-10-07T14:15Z", "family": "Visibility", "description": "By day, from sunrise to mid-afternoon: the error_value of all sensors, references included, rises at sunrise and comes back down in the afternoon; the reference R3 is rejected almost all day, as every day (Target issue, separate label). The corrected curves of the targets are markedly more agitated than in the evening, without a clean step. At sunrise, PA_9, PB4 and PB_5 are rejected at the first measurements; from 11:30 to 12:45, vehicles pass (separate labels). Cause: daytime heat shimmer above the road and the low sun at sunrise, as every day on this station; not seen directly, the images show the scene in full daylight, the spots of the reflectors drowned in the light background. Overall compensated: the structure is not moving, do not trust the small oscillations of the day.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-179", "start": "2026-10-07T11:15Z", "end": "2026-10-07T11:45Z", "family": "Obstruction", "description": "At 11:30, PA3_2, PB4 and PB_5 are rejected for the time of one measurement, with the references PA1_2 and R2; the other targets barely move. A vehicle passes on the road in front of the row of targets, seen as translucent, in repeated blurry copies, on the 11:30 image. Everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-180", "start": "2026-10-07T11:45Z", "end": "2026-10-07T12:30Z", "family": "Obstruction", "description": "At 12:00, blurry trails pass over the references R1 and R2 (12:00 thumbnails), probably a vehicle: they are set aside, PB4 rejected, and the basis changes for the time of one measurement; PA3_2, PB_5, PB1_2 and PB2_2 jump together, then come back at the next measurement; PA3_2 is still rejected alone at 12:15, blurry translucent shapes on its thumbnail: the same passage, everything has come back at 12:30. The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-181", "start": "2026-10-07T12:30Z", "end": "2026-10-07T13:00Z", "family": "Obstruction", "description": "The lights of a vehicle appear near PB4 and the reference R2 (12:45 thumbnails, absent at 12:30): PB4 and R2 are rejected for the time of one measurement. The other targets do not move; everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-182", "start": "2026-10-07T13:30Z", "end": "2026-10-08T05:30Z", "family": "No data", "description": "No measurement for any sensor during the night, the outage starting as early as the start of the afternoon, except one isolated measurement at 14:15. The station shuts down for lack of energy: just before the outage, the battery is at its lowest and the voltage below its usual night level, and the metrics stop with the measurements; it restarts at sunrise with the solar charge, the compute board still cold (metrics). The curves are missing; nothing moves on the structure, but the station does not have enough energy to last the night: to be checked (battery, panel).", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-183", "start": "2026-10-07T13:30Z", "end": "2026-10-08T13:30Z", "family": "Displacement", "description": "PB2_2, then PB1_2 again, neighbours on the pavement kerb, go down on corr_x during the outage of the night from 07 to 08/10: they are lower from the restart on the morning of 08/10, PB2_2 more markedly, PB1_2 keeps going down in the morning under the loss of the reference PA1_2 (labelled separately), and they stay lower after the return of PA1_2 (13:15) and the next day, with all the references (09/10 from 06:15), until the outage of 09/10: no return seen. This is the second step of the descent of PB1_2 from 06/10, labelled separately. Their raw positions have shifted a little, alone, relative to the set of targets; their spots stay round and sharp (08/10 16:00 thumbnail) and their error_value does not change level. Cause not established: a movement of the kerb is not excluded. To be checked: look at the targets PB1_2 and PB2_2, keep watching.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-184", "start": "2026-10-08T05:30Z", "end": "2026-10-08T13:00Z", "family": "Thermal displacement", "description": "From sunrise until around noon, the camera moves through thermal effect, as every day: its tilt rises little at sunrise (from 05:30 to 06:30-06:45, a little above its afternoon rest; markedly higher at 08:30, on a single measurement); it goes below this rest in late morning (at 10:30) and regains it at 11:45. The scale, for its part, does not rise that day. The rotation does not do its cycle: it stayed at its level until 09:00, drops markedly from 09:15 to 13:00 and holds, a little less low, in the afternoon and on 09/10, with no return; this is not the effect of the reference PA1_2, already set aside since 06:15, since the rotation stays at this low level after its return at 13:15 and with the six references at 15:00. The pan drops likewise (markedly from 07:15 to 13:15, a little less low in the afternoon). In the image, targets and references move together, as a block: y markedly positive at 08:30 (the measurement of the jump), then a little negative at 10:30; the block of targets turned like the pose between morning and afternoon: the camera did turn, and the compensation follows (ensemble.py --rigide; the targets move away from the block only barely). The housing temperature rises strongly from 04h to 10h and stays hot at 11h: the tilt rises with the warming of the morning and comes back while the housing is still hot. The compensation follows the wave: there are too few measurements with all the references to say so target by target (PA1_2 set aside almost the whole morning); on the measurements where R1, R2 and PB3_2 are retained, no more than a little; what remains is the daytime agitation, the passages, the steps of the loss of PA1_2 and the descent of PB1_2 and PB2_2 (separate labels). Cause given by the expert for this station (label of 27/09) for the daily cycle: thermal effect on the lens or the mount of the camera; the road does not move with temperature. The rotation that does not come back is not explained by the temperature (cause not established): this is not a movement of the road, the targets follow it as a block and the compensation follows it, except perhaps for PB1_2 and PB2_2, whose descent is labelled separately (link not established); the camera movement is to be watched. The daily cycle, for its part, is normal.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-185", "start": "2026-10-08T05:30Z", "end": "2026-10-08T15:00Z", "family": "Visibility", "description": "By day, from sunrise to mid-afternoon: the error_value of all sensors, references included, rises at sunrise and comes back down in the afternoon; the reference R3 is rejected almost all day, as every day (Target issue, separate label). The corrected curves of the targets are markedly more agitated than in the evening, without a clean step. At sunrise, PA3_2, PA_9, PB4 and PB_5 are rejected for nearly an hour, PA_9 until mid-morning; at 12:15 and 12:45, passages (separate labels). Cause: daytime heat shimmer above the road and the low sun at sunrise, as every day on this station; not seen directly, the images show the scene in full daylight, the spots of the reflectors drowned in the light background. Overall compensated: the structure is not moving, do not trust the small oscillations of the day.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-186", "start": "2026-10-08T06:00Z", "end": "2026-10-08T13:15Z", "family": "Visibility", "description": "The reference PA1_2 is rejected almost the whole morning: on its thumbnails, the pavement in full sun is very bright and its spot is hard to make out there (08:30, 10:00), while it is sharp later (13:15). Without it, the basis changes and the rotation of the camera shifts: PB1_2, PB2_2, PA2_2 and PB_5 drop on corr_x in a step, PB1_2 and PB2_2 the most; at the brief returns of PA1_2, they rise back a little. When PA1_2 is taken again at 13:15, PA2_2 and PB_5 come back, PB1_2 and PB2_2 not quite (separate label). Cause: the daylight on the pavement around PA1_2. The steps are not a movement: curves not to be trusted over the range.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-187", "start": "2026-10-08T11:30Z", "end": "2026-10-08T12:00Z", "family": "Obstruction", "description": "At 11:45, a blurry trail passes over the references R1 and R2 (11:45 thumbnails), probably a vehicle: they are set aside, PA3_2 and PA_9 rejected, and the basis changes for the time of one measurement; PB4 and PB_5 jump on corr_x, PB1_2 and PB2_2 rise back, then everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-188", "start": "2026-10-08T12:00Z", "end": "2026-10-08T12:30Z", "family": "Obstruction", "description": "A vehicle passes in front of PA3_2, PB4 and the reference R2, seen as translucent (wheel, lights) on their 12:15 thumbnails: PA3_2, PA_9 and PB4 are rejected for the time of one measurement, with R2. The other targets do not move; everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-189", "start": "2026-10-08T12:30Z", "end": "2026-10-08T13:00Z", "family": "Obstruction", "description": "For the time of one measurement, PB1_2 and PB2_2 are rejected together, with the reference R2: on their 12:45 thumbnails, blurry silhouettes pass translucent on the pavement, probably passers-by. Everything comes back at the next measurement for these targets; the step of 13:00 comes from the reference PA1_2 (separate label). The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-190", "start": "2026-10-08T14:00Z", "end": "2026-10-08T14:30Z", "family": "Visibility", "description": "At 14:15, the image is very dark (thumbnails of R1, R2 and PB4 almost black): R1 and R2 are set aside, PA3_2 and PB4 rejected, and the basis changes for the time of one measurement; PB_5, PB1_2 and PB2_2 jump together, then come back at the next measurement. Cause: a capture that is too dark. The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-191", "start": "2026-10-08T14:30Z", "end": "2026-10-08T15:00Z", "family": "Visibility", "description": "At 14:45, again a very dark image: R1 and R2 are set aside, and PB4, PA3_2, PB_5 and PB1_2 jump together for the time of one measurement, then come back. Cause: a capture that is too dark, as at 14:15. The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-192", "start": "2026-10-08T16:00Z", "end": "2026-10-09T05:00Z", "family": "No data", "description": "No measurement for any sensor during the night. The station shuts down for lack of energy: just before the outage, the battery is at its lowest and the voltage below its usual night level, and the metrics stop with the measurements; it restarts at sunrise with the solar charge, the compute board still cold (metrics). The curves are missing; nothing moves on the structure, but the station does not have enough energy to last the night: to be checked (battery, panel).", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-193", "start": "2026-10-09T05:00Z", "end": "2026-10-09T12:30Z", "family": "Thermal displacement", "description": "From sunrise until around noon, the camera moves through thermal effect, as every day: until 06:00, without PA1_2, R1 and R2, the pose is distorted; afterwards, with all the references, its tilt rises (the camera nods down) from 06:15 to 07:45-08:00, later and less high than the other days, goes below the afternoon level of 08/10 in late morning (at 10:30 and 11:30) and regains it at 11:45; the measurements stop at 12:30. The pan and the rotation rise in mid-morning (the pan a little, at 10:15, the rotation markedly, at 10:30) and come back at 11:45-12:15, the rotation to the afternoon level of 08/10, not to that of before 08/10; the scale does not rise. In the image, targets and references move together, as a block: y a little positive at 06:00, then a little less negative at 10:15 (ensemble.py --rigide; the targets move away from the block only barely). The housing temperature rises strongly from 04h to 09h and stays hot at 12h: the tilt rises with the warming of the morning and comes back while the housing is still hot. The compensation follows: on the corrected curves, the tilt wave weighs only a little on each target; what remains is the daytime agitation and the passages (separate labels). Cause given by the expert for this station (label of 27/09): the camera moves through thermal effect, on its lens or its mount; the road does not move with temperature. Normal, nothing to do.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-194", "start": "2026-10-09T05:00Z", "end": "2026-10-09T12:30Z", "family": "Visibility", "description": "By day, from sunrise to mid-afternoon: the error_value of all sensors, references included, rises at sunrise and comes back down in the afternoon; the reference R3 is rejected almost all day, as every day (Target issue, separate label). The corrected curves of the targets are markedly more agitated than in the evening, without a clean step. At sunrise, the compensation loses all its references from 05:00 to 05:30: PA3_2, PA_9, PB4 and PB_5 are rejected for an hour, PA2_2, PB1_2 and PB2_2 stay measured and jump. In the morning, PA1_2 and PA_8 are set aside at times, PA_9 rejected in late morning; at 09:30, a car passes in front of PB_5 and the reference PB3_2 (separate label). The measurements stop at 12:30. Cause: daytime heat shimmer above the road and the low sun at sunrise, as every day on this station; not seen directly, the images show the scene in full daylight, the spots of the reflectors drowned in the light background. Overall compensated: the structure is not moving, do not trust the small oscillations of the day.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-195", "start": "2026-10-09T09:15Z", "end": "2026-10-09T09:45Z", "family": "Obstruction", "description": "At 09:30, a car passes in front of the bottom row, clearly seen on the thumbnails of PA3_2, PB2_2, PB4 and PB_5 (bodywork, wheel): PB_5 and the reference PB3_2 are rejected for the time of one measurement; the other targets, which stayed under the threshold, do not jump. Everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-196", "start": "2026-10-09T11:45Z", "end": "2026-10-09T12:15Z", "family": "Obstruction", "description": "Bright vehicle reflections appear near PA3_2 and PB4 (12:00 thumbnails, absent at 11:45): having stayed under the threshold, they lock onto them and their corr_x, corr_y make a huge jump for the time of one measurement; the reference R2 is set aside. Everything comes back at the next measurement. The structure is not moving: these points are false, to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-197", "start": "2026-10-09T12:30Z", "end": "2026-10-15T08:00Z", "family": "No data", "description": "No measurement for any sensor for nearly six days. Until the early morning of 13/10, the station is mute: no metrics and no images, although the battery was not low just before (metrics of 09/10 at noon), so this is not the outage of each night. From 13/10, the metrics come back, the battery full and stable at night, and daytime images arrive every hour, but still no displacement measurement. Cause not established (station stopped, then measurement that does not restart; an intervention is possible). The curves are missing: to be checked with the operator.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-198", "start": "2026-10-15T07:45Z", "end": "2026-10-15T08:15Z", "family": "Obstruction", "description": "A single measurement, in the middle of the outage: all the references are rejected, the camera is not recalibrated, PA2_2, PA3_2, PB2_2 and PB4 are rejected; PA_9, PB1_2 and PB_5 keep a point, very far from their level. The 08:00 image shows translucent blurry trails on the pavement and the road, like the passages seen on the other days. Probable cause: a passage in front of the scene; without any reference, these points are meaningless. The structure is not moving: points to ignore.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-199", "start": "2026-10-15T08:00Z", "end": "2026-10-31T20:15Z", "family": "No data", "description": "No measurement for any sensor for more than two weeks; the metrics and the images are also missing almost all that time (two isolated values on 25/10), and come back only on 30/10 in the evening, the battery full, with daytime images on 31/10, still without a displacement measurement. Cause not established (station stopped). The curves are missing: to be checked with the operator.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-200", "start": "2026-10-31T20:00Z", "end": "2026-10-31T20:30Z", "family": "Displacement", "description": "A single measurement after three weeks without measurement: the camera has nodded down a lot since 09/10 (its tilt well above that of early October, already slowly rising from 03/10 to 09/10), all the raw positions have risen in the image. The compensation runs on five references (R2 rejected), but almost all targets have their corrected curves shifted upward on corr_y, PB1_2 and PB2_2 the most, PA_9 on corr_x, and the reprojection errors of the references are higher than usual. No image at that hour. Cause not established: the camera has tilted, and the compensation does not quite catch up with it; a single point does not say whether it is lasting. To be checked: look at the mount of the camera, keep watching the next measurements.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-201", "start": "2026-10-31T20:15Z", "end": "2026-11-01T00:00Z", "family": "No data", "description": "No measurement for any sensor until the end of the batch; the metrics stop at the same moment, although the battery was full and the voltage normal. This is not an end-of-file delay: nothing arrives on the following days either, when the other stations have their data. Cause not established (station stopped again). The curves are missing: to be checked with the operator.", "review": "2026-11-17"}
|
||||
{"id": "WILDSTRUBEL-200", "start": "2026-10-31T20:00Z", "end": "2026-10-31T20:30Z", "family": "Displacement", "description": "A single measurement after three weeks without measurement: the camera has nodded down a lot since 09/10 (its tilt well above that of early October, already slowly rising from 03/10 to 09/10), all the raw positions have risen in the image. The compensation runs on five references (R2 rejected), but almost all targets have their corrected curves shifted upward on corr_y, PB1_2 and PB2_2 the most, PA_9 on corr_x, and the reprojection errors of the references are higher than usual. No image at that hour. Cause not established: the camera has tilted, and the compensation does not quite catch up with it; a single point does not say whether it is lasting. To be checked: look at the mount of the camera, keep watching the next measurements.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-20T0000_2026-11-01T0000"}
|
||||
{"id": "WILDSTRUBEL-201", "start": "2026-10-31T20:15Z", "end": "2026-11-01T00:00Z", "family": "No data", "description": "No measurement for any sensor until the end of the batch; the metrics stop at the same moment, although the battery was full and the voltage normal. This is not an end-of-file delay: nothing arrives on the following days either, when the other stations have their data. Cause not established (station stopped again). The curves are missing: to be checked with the operator.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-20T0000_2026-11-01T0000"}
|
||||
{"id": "WILDSTRUBEL-176", "start": "2026-10-06T19:45Z", "end": "2026-10-07T07:00Z", "family": "No data", "description": "No measurement for any sensor during the night, except three isolated measurements at 05:00, 06:00 and 06:30, where several targets are rejected. The station shuts down for lack of energy: just before the outage, the battery is at its lowest and the voltage below its usual night level, and the metrics stop with the measurements; it restarts at sunrise with the solar charge, the compute board still cold (metrics). The curves are missing; nothing moves on the structure, but the station does not have enough energy to last the night: to be checked (battery, panel).", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-177", "start": "2026-10-07T05:00Z", "end": "2026-10-07T12:00Z", "family": "Thermal displacement", "description": "From sunrise until around noon, the camera moves through thermal effect, as every day: its tilt rises (the camera nods down) from 05:00, already a little above its early-afternoon level, to 06:30, markedly above; it goes below this level in late morning (at 11:15) and regains it at 12:00. The pan drops a little at sunrise (at 06:30) then rises a little (at 10:15); the rotation goes markedly above its 05:00 level (at 10:15) and comes back at 12:15-13:15; the scale rises with the temperature (at 07:45) and comes back down from 12:00. In the image, targets and references move together, as a block: y a little positive at 07:15, then a little less negative at 11:15 (ensemble.py --rigide; the targets move away from the block only barely). The housing temperature rises strongly from 04h to 08h and stays hot at 12h: the tilt rises with the warming of the morning and comes back while the housing is still hot; the scale follows the temperature and comes back down with it. The compensation follows: on the corrected curves, the tilt wave weighs on each target only barely more than the noise; what remains is the daytime agitation and the passages (separate labels). Cause given by the expert for this station (label of 27/09): the camera moves through thermal effect, on its lens or its mount; the road does not move with temperature. Normal, nothing to do.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-178", "start": "2026-10-07T05:00Z", "end": "2026-10-07T14:15Z", "family": "Visibility", "description": "By day, from sunrise to mid-afternoon: the error_value of all sensors, references included, rises at sunrise and comes back down in the afternoon; the reference R3 is rejected almost all day, as every day (Target issue, separate label). The corrected curves of the targets are markedly more agitated than in the evening, without a clean step. At sunrise, PA_9, PB4 and PB_5 are rejected at the first measurements; from 11:30 to 12:45, vehicles pass (separate labels). Cause: daytime heat shimmer above the road and the low sun at sunrise, as every day on this station; not seen directly, the images show the scene in full daylight, the spots of the reflectors drowned in the light background. Overall compensated: the structure is not moving, do not trust the small oscillations of the day.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-179", "start": "2026-10-07T11:15Z", "end": "2026-10-07T11:45Z", "family": "Obstruction", "description": "At 11:30, PA3_2, PB4 and PB_5 are rejected for the time of one measurement, with the references PA1_2 and R2; the other targets barely move. A vehicle passes on the road in front of the row of targets, seen as translucent, in repeated blurry copies, on the 11:30 image. Everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-180", "start": "2026-10-07T11:45Z", "end": "2026-10-07T12:30Z", "family": "Obstruction", "description": "At 12:00, blurry trails pass over the references R1 and R2 (12:00 thumbnails), probably a vehicle: they are set aside, PB4 rejected, and the basis changes for the time of one measurement; PA3_2, PB_5, PB1_2 and PB2_2 jump together, then come back at the next measurement; PA3_2 is still rejected alone at 12:15, blurry translucent shapes on its thumbnail: the same passage, everything has come back at 12:30. The structure is not moving: point to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-181", "start": "2026-10-07T12:30Z", "end": "2026-10-07T13:00Z", "family": "Obstruction", "description": "The lights of a vehicle appear near PB4 and the reference R2 (12:45 thumbnails, absent at 12:30): PB4 and R2 are rejected for the time of one measurement. The other targets do not move; everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-182", "start": "2026-10-07T13:30Z", "end": "2026-10-08T05:30Z", "family": "No data", "description": "No measurement for any sensor during the night, the outage starting as early as the start of the afternoon, except one isolated measurement at 14:15. The station shuts down for lack of energy: just before the outage, the battery is at its lowest and the voltage below its usual night level, and the metrics stop with the measurements; it restarts at sunrise with the solar charge, the compute board still cold (metrics). The curves are missing; nothing moves on the structure, but the station does not have enough energy to last the night: to be checked (battery, panel).", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-183", "start": "2026-10-07T13:30Z", "end": "2026-10-08T13:30Z", "family": "Displacement", "description": "PB2_2, then PB1_2 again, neighbours on the pavement kerb, go down on corr_x during the outage of the night from 07 to 08/10: they are lower from the restart on the morning of 08/10, PB2_2 more markedly, PB1_2 keeps going down in the morning under the loss of the reference PA1_2 (labelled separately), and they stay lower after the return of PA1_2 (13:15) and the next day, with all the references (09/10 from 06:15), until the outage of 09/10: no return seen. This is the second step of the descent of PB1_2 from 06/10, labelled separately. Their raw positions have shifted a little, alone, relative to the set of targets; their spots stay round and sharp (08/10 16:00 thumbnail) and their error_value does not change level. Cause not established: a movement of the kerb is not excluded. To be checked: look at the targets PB1_2 and PB2_2, keep watching.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-184", "start": "2026-10-08T05:30Z", "end": "2026-10-08T13:00Z", "family": "Thermal displacement", "description": "From sunrise until around noon, the camera moves through thermal effect, as every day: its tilt rises little at sunrise (from 05:30 to 06:30-06:45, a little above its afternoon rest; markedly higher at 08:30, on a single measurement); it goes below this rest in late morning (at 10:30) and regains it at 11:45. The scale, for its part, does not rise that day. The rotation does not do its cycle: it stayed at its level until 09:00, drops markedly from 09:15 to 13:00 and holds, a little less low, in the afternoon and on 09/10, with no return; this is not the effect of the reference PA1_2, already set aside since 06:15, since the rotation stays at this low level after its return at 13:15 and with the six references at 15:00. The pan drops likewise (markedly from 07:15 to 13:15, a little less low in the afternoon). In the image, targets and references move together, as a block: y markedly positive at 08:30 (the measurement of the jump), then a little negative at 10:30; the block of targets turned like the pose between morning and afternoon: the camera did turn, and the compensation follows (ensemble.py --rigide; the targets move away from the block only barely). The housing temperature rises strongly from 04h to 10h and stays hot at 11h: the tilt rises with the warming of the morning and comes back while the housing is still hot. The compensation follows the wave: there are too few measurements with all the references to say so target by target (PA1_2 set aside almost the whole morning); on the measurements where R1, R2 and PB3_2 are retained, no more than a little; what remains is the daytime agitation, the passages, the steps of the loss of PA1_2 and the descent of PB1_2 and PB2_2 (separate labels). Cause given by the expert for this station (label of 27/09) for the daily cycle: thermal effect on the lens or the mount of the camera; the road does not move with temperature. The rotation that does not come back is not explained by the temperature (cause not established): this is not a movement of the road, the targets follow it as a block and the compensation follows it, except perhaps for PB1_2 and PB2_2, whose descent is labelled separately (link not established); the camera movement is to be watched. The daily cycle, for its part, is normal.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-185", "start": "2026-10-08T05:30Z", "end": "2026-10-08T15:00Z", "family": "Visibility", "description": "By day, from sunrise to mid-afternoon: the error_value of all sensors, references included, rises at sunrise and comes back down in the afternoon; the reference R3 is rejected almost all day, as every day (Target issue, separate label). The corrected curves of the targets are markedly more agitated than in the evening, without a clean step. At sunrise, PA3_2, PA_9, PB4 and PB_5 are rejected for nearly an hour, PA_9 until mid-morning; at 12:15 and 12:45, passages (separate labels). Cause: daytime heat shimmer above the road and the low sun at sunrise, as every day on this station; not seen directly, the images show the scene in full daylight, the spots of the reflectors drowned in the light background. Overall compensated: the structure is not moving, do not trust the small oscillations of the day.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-186", "start": "2026-10-08T06:00Z", "end": "2026-10-08T13:15Z", "family": "Visibility", "description": "The reference PA1_2 is rejected almost the whole morning: on its thumbnails, the pavement in full sun is very bright and its spot is hard to make out there (08:30, 10:00), while it is sharp later (13:15). Without it, the basis changes and the rotation of the camera shifts: PB1_2, PB2_2, PA2_2 and PB_5 drop on corr_x in a step, PB1_2 and PB2_2 the most; at the brief returns of PA1_2, they rise back a little. When PA1_2 is taken again at 13:15, PA2_2 and PB_5 come back, PB1_2 and PB2_2 not quite (separate label). Cause: the daylight on the pavement around PA1_2. The steps are not a movement: curves not to be trusted over the range.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-187", "start": "2026-10-08T11:30Z", "end": "2026-10-08T12:00Z", "family": "Obstruction", "description": "At 11:45, a blurry trail passes over the references R1 and R2 (11:45 thumbnails), probably a vehicle: they are set aside, PA3_2 and PA_9 rejected, and the basis changes for the time of one measurement; PB4 and PB_5 jump on corr_x, PB1_2 and PB2_2 rise back, then everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-188", "start": "2026-10-08T12:00Z", "end": "2026-10-08T12:30Z", "family": "Obstruction", "description": "A vehicle passes in front of PA3_2, PB4 and the reference R2, seen as translucent (wheel, lights) on their 12:15 thumbnails: PA3_2, PA_9 and PB4 are rejected for the time of one measurement, with R2. The other targets do not move; everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-189", "start": "2026-10-08T12:30Z", "end": "2026-10-08T13:00Z", "family": "Obstruction", "description": "For the time of one measurement, PB1_2 and PB2_2 are rejected together, with the reference R2: on their 12:45 thumbnails, blurry silhouettes pass translucent on the pavement, probably passers-by. Everything comes back at the next measurement for these targets; the step of 13:00 comes from the reference PA1_2 (separate label). The structure is not moving: point to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-190", "start": "2026-10-08T14:00Z", "end": "2026-10-08T14:30Z", "family": "Visibility", "description": "At 14:15, the image is very dark (thumbnails of R1, R2 and PB4 almost black): R1 and R2 are set aside, PA3_2 and PB4 rejected, and the basis changes for the time of one measurement; PB_5, PB1_2 and PB2_2 jump together, then come back at the next measurement. Cause: a capture that is too dark. The structure is not moving: point to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-191", "start": "2026-10-08T14:30Z", "end": "2026-10-08T15:00Z", "family": "Visibility", "description": "At 14:45, again a very dark image: R1 and R2 are set aside, and PB4, PA3_2, PB_5 and PB1_2 jump together for the time of one measurement, then come back. Cause: a capture that is too dark, as at 14:15. The structure is not moving: point to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-192", "start": "2026-10-08T16:00Z", "end": "2026-10-09T05:00Z", "family": "No data", "description": "No measurement for any sensor during the night. The station shuts down for lack of energy: just before the outage, the battery is at its lowest and the voltage below its usual night level, and the metrics stop with the measurements; it restarts at sunrise with the solar charge, the compute board still cold (metrics). The curves are missing; nothing moves on the structure, but the station does not have enough energy to last the night: to be checked (battery, panel).", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-193", "start": "2026-10-09T05:00Z", "end": "2026-10-09T12:30Z", "family": "Thermal displacement", "description": "From sunrise until around noon, the camera moves through thermal effect, as every day: until 06:00, without PA1_2, R1 and R2, the pose is distorted; afterwards, with all the references, its tilt rises (the camera nods down) from 06:15 to 07:45-08:00, later and less high than the other days, goes below the afternoon level of 08/10 in late morning (at 10:30 and 11:30) and regains it at 11:45; the measurements stop at 12:30. The pan and the rotation rise in mid-morning (the pan a little, at 10:15, the rotation markedly, at 10:30) and come back at 11:45-12:15, the rotation to the afternoon level of 08/10, not to that of before 08/10; the scale does not rise. In the image, targets and references move together, as a block: y a little positive at 06:00, then a little less negative at 10:15 (ensemble.py --rigide; the targets move away from the block only barely). The housing temperature rises strongly from 04h to 09h and stays hot at 12h: the tilt rises with the warming of the morning and comes back while the housing is still hot. The compensation follows: on the corrected curves, the tilt wave weighs only a little on each target; what remains is the daytime agitation and the passages (separate labels). Cause given by the expert for this station (label of 27/09): the camera moves through thermal effect, on its lens or its mount; the road does not move with temperature. Normal, nothing to do.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-194", "start": "2026-10-09T05:00Z", "end": "2026-10-09T12:30Z", "family": "Visibility", "description": "By day, from sunrise to mid-afternoon: the error_value of all sensors, references included, rises at sunrise and comes back down in the afternoon; the reference R3 is rejected almost all day, as every day (Target issue, separate label). The corrected curves of the targets are markedly more agitated than in the evening, without a clean step. At sunrise, the compensation loses all its references from 05:00 to 05:30: PA3_2, PA_9, PB4 and PB_5 are rejected for an hour, PA2_2, PB1_2 and PB2_2 stay measured and jump. In the morning, PA1_2 and PA_8 are set aside at times, PA_9 rejected in late morning; at 09:30, a car passes in front of PB_5 and the reference PB3_2 (separate label). The measurements stop at 12:30. Cause: daytime heat shimmer above the road and the low sun at sunrise, as every day on this station; not seen directly, the images show the scene in full daylight, the spots of the reflectors drowned in the light background. Overall compensated: the structure is not moving, do not trust the small oscillations of the day.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-195", "start": "2026-10-09T09:15Z", "end": "2026-10-09T09:45Z", "family": "Obstruction", "description": "At 09:30, a car passes in front of the bottom row, clearly seen on the thumbnails of PA3_2, PB2_2, PB4 and PB_5 (bodywork, wheel): PB_5 and the reference PB3_2 are rejected for the time of one measurement; the other targets, which stayed under the threshold, do not jump. Everything comes back at the next measurement. The structure is not moving: point to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-196", "start": "2026-10-09T11:45Z", "end": "2026-10-09T12:15Z", "family": "Obstruction", "description": "Bright vehicle reflections appear near PA3_2 and PB4 (12:00 thumbnails, absent at 11:45): having stayed under the threshold, they lock onto them and their corr_x, corr_y make a huge jump for the time of one measurement; the reference R2 is set aside. Everything comes back at the next measurement. The structure is not moving: these points are false, to ignore.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-197", "start": "2026-10-09T12:30Z", "end": "2026-10-15T08:00Z", "family": "No data", "description": "No measurement for any sensor for nearly six days. Until the early morning of 13/10, the station is mute: no metrics and no images, although the battery was not low just before (metrics of 09/10 at noon), so this is not the outage of each night. From 13/10, the metrics come back, the battery full and stable at night, and daytime images arrive every hour, but still no displacement measurement. Cause not established (station stopped, then measurement that does not restart; an intervention is possible). The curves are missing: to be checked with the operator.", "review": "2026-11-17", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
{"id": "WILDSTRUBEL-202", "start": "2026-10-15T07:45Z", "end": "2026-10-15T08:15Z", "family": "Obstruction", "description": "A single measurement, in the middle of the outage, at 08:00: five of the six references are rejected (PA1_2, PA_8, PB3_2, R2, R3); R1 alone is kept, so the compensation can only remove a translation and the camera is not properly recalibrated. PA2_2, PA3_2, PB2_2 and PB4 are rejected; PA_9, PB1_2 and PB_5 keep a point, clearly far from their level in corr_y. Their raw positions show the whole scene shifted downward by a large step since the last measurements of 09/10: the camera moved during the outage, cause not established (an intervention is possible). The 08:00 image shows translucent blurry trails on the pavement and the road, like the passages seen on the other days. Probable cause of the rejections: a passage in front of the scene, on top of the shifted camera. With a single reference, these points are meaningless: points to ignore; the camera position is to be checked with the operator.", "analysis": "WILDSTRUBEL_2026-10-06T1945_2026-10-20T0000"}
|
||||
Reference in new issue
Block a user