Files
aimsight-libredesk/snippets/textes/station-guide-quick-start-cellular-monitoring-installation.md
T
maximeandClaude Opus 5.5 10ed887417 Noms plus clairs : snippets/, scripts de test numérotés, verifier_ollama.py
- base_connaissances/ → snippets/ (corpus/ → textes/, instructions.md → consignes_redaction.md, decoupage.py → fichiers.py, importer.py → envoyer.py) ; python3 -m snippets.envoyer.
- instance-de-test/ : 1_demarrer.sh, 2_creer_boite_et_cle.py, 3_brancher_ia.py, 4_essayer_brouillons.py, voir_empreintes.sh, connexion_admin.py.
- ollama/verifier.py → ollama/verifier_ollama.py ; tests, tâches VS Code et docs alignés.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-12 10:27:06 +01:00

3.9 KiB

Station Guide — Quick Start — Cellular Monitoring Installation

Use this checklist to bring a monitoring station online through the cellular network:

  1. With the system powered off, install an activated 3FF / Micro SIM card with a suitable mobile-data plan.
  2. Connect the supplied cellular antenna using the supplied SMA cable(s).
  3. Connect the power supply.
  4. Turn the system on and wait for it to boot.
  5. Connect locally to the web interface, normally at 192.168.1.2, using the supplied Ethernet cable.
  6. Open Settings / Network Settings.
  7. Enter the APN provided by the SIM-card operator in the Cellular Network section.
  8. Click Apply Network Settings.
  9. Wait for the modem to register on the network. The Link status in the Cellular Network section should change to Up. When the link status is Up, the station is connected through the cellular network and can be reached remotely according to the SIM subscription, network routing, and monitoring-platform configuration. The cellular module uses a 3FF / Micro SIM card. The SIM card must be activated and configured with a mobile data plan suitable for the intended use. A static IP address is not required. CAUTION Make sure that the SIM card data allowance is high enough for the planned operation. If raw, full-quality images or videos are transmitted over the 4G connection, the data volume can quickly become very large.
  10. Power OFF the system and wait until the modem is completely off.
  11. Carefully access and lift the modem module. If a SIM card is already installed, remove it from the SIM card slot.
  12. Insert the Micro SIM card into the SIM card slot in the correct orientation. Make sure the SIM card is fully seated.
  13. Reinstall the modem module onto the AIMsight board. Before powering the product back on, carefully check that the modem pins are correctly aligned with the AIMsight board connection pins. Do not power on the product if the modem is offset, tilted, only partially inserted, or misaligned. Incorrect alignment may prevent normal operation and may damage the modem or the AIMsight board.
  14. Check that the internal antenna connectors are installed and connected correctly.
  15. Connect the supplied cellular antenna to the station using the supplied SMA cable(s).
  16. Mount the cellular antenna in a clear location with good sky exposure whenever possible, away from metallic structures, metal surfaces, metal enclosures, other obstructions, other transmitting antennas, and radio equipment, to reduce signal degradation and improve reception.
  17. Ensure that the antenna is installed for operation at least 20 cm away from the operator and other persons during normal use.
  18. Power the system on again and wait for the modem to start.
  19. Go to the System / Network Configuration page, set the correct APN for your SIM card/ operator, and check the cellular connection status in System Settings (see page 18). After entering or changing the APN, click Apply Network Settings. Allow time for network registration, then verify that the Link status under Cellular Network changes to Up. SIM card installation or replacement procedure: 1. power the system off; 2. access and lift the modem module to reach the SIM card slot underneath; 3. insert the SIM card in the correct orientation; 4., 5. reinstall the modem module, ensuring that the modem pins are correctly aligned with the AIMsight board connection pins; 6. check that the antenna connections are properly installed. CAUTION Use only the supplied or approved antenna and cable assembly. Changes to the antenna, cable, connector, or mounting arrangement may reduce performance and can affect regulatory compliance. CAUTION Do not install or operate the cellular antenna close to the body. The antenna is intended for fixed or mobile installation only and must be used with a minimum separation distance of 20 cm from any person during normal operation.

Source : AIMsight Station Guide, rév. 1.5