- base_connaissances/ → snippets/ (corpus/ → textes/, instructions.md → consignes_redaction.md, decoupage.py → fichiers.py, importer.py → envoyer.py) ; python3 -m snippets.envoyer. - instance-de-test/ : 1_demarrer.sh, 2_creer_boite_et_cle.py, 3_brancher_ia.py, 4_essayer_brouillons.py, voir_empreintes.sh, connexion_admin.py. - ollama/verifier.py → ollama/verifier_ollama.py ; tests, tâches VS Code et docs alignés. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
63 lines
3.9 KiB
Markdown
63 lines
3.9 KiB
Markdown
# Station Guide — Quick Start — Cellular Monitoring Installation
|
|
|
|
Use this checklist to bring a monitoring station online through the cellular network:
|
|
1. With the system powered off, install an activated 3FF / Micro SIM card with a suitable
|
|
mobile-data plan.
|
|
2. Connect the supplied cellular antenna using the supplied SMA cable(s).
|
|
3. Connect the power supply.
|
|
4. Turn the system on and wait for it to boot.
|
|
5. Connect locally to the web interface, normally at 192.168.1.2, using the supplied Ethernet
|
|
cable.
|
|
6. Open Settings / Network Settings.
|
|
7. Enter the APN provided by the SIM-card operator in the Cellular Network section.
|
|
8. Click Apply Network Settings.
|
|
9. Wait for the modem to register on the network. The Link status in the Cellular Network
|
|
section should change to Up.
|
|
When the link status is Up, the station is connected through the cellular network and can be
|
|
reached remotely according to the SIM subscription, network routing, and monitoring-platform
|
|
configuration.
|
|
The cellular module uses a 3FF / Micro SIM card. The SIM card must be activated and
|
|
configured with a mobile data plan suitable for the intended use. A static IP address is not
|
|
required.
|
|
CAUTION
|
|
Make sure that the SIM card data allowance is high enough for the planned operation. If raw,
|
|
full-quality images or videos are transmitted over the 4G connection, the data volume can
|
|
quickly become very large.
|
|
1. Power OFF the system and wait until the modem is completely off.
|
|
2. Carefully access and lift the modem module. If a SIM card is already installed, remove it
|
|
from the SIM card slot.
|
|
3. Insert the Micro SIM card into the SIM card slot in the correct orientation. Make sure the
|
|
SIM card is fully seated.
|
|
4. Reinstall the modem module onto the AIMsight board. Before powering the product back
|
|
on, carefully check that the modem pins are correctly aligned with the AIMsight board
|
|
connection pins. Do not power on the product if the modem is offset, tilted, only
|
|
partially inserted, or misaligned. Incorrect alignment may prevent normal operation and
|
|
may damage the modem or the AIMsight board.
|
|
5. Check that the internal antenna connectors are installed and connected correctly.
|
|
6. Connect the supplied cellular antenna to the station using the supplied SMA cable(s).
|
|
7. Mount the cellular antenna in a clear location with good sky exposure whenever possible,
|
|
away from metallic structures, metal surfaces, metal enclosures, other obstructions, other
|
|
transmitting antennas, and radio equipment, to reduce signal degradation and improve
|
|
reception.
|
|
8. Ensure that the antenna is installed for operation at least 20 cm away from the operator
|
|
and other persons during normal use.
|
|
9. Power the system on again and wait for the modem to start.
|
|
10. Go to the System / Network Configuration page, set the correct APN for your SIM card/
|
|
operator, and check the cellular connection status in System Settings (see page 18).
|
|
After entering or changing the APN, click Apply Network Settings. Allow time for network
|
|
registration, then verify that the Link status under Cellular Network changes to Up.
|
|
SIM card installation or replacement procedure: 1. power the system off; 2. access and lift the modem
|
|
module to reach the SIM card slot underneath; 3. insert the SIM card in the correct orientation; 4., 5.
|
|
reinstall the modem module, ensuring that the modem pins are correctly aligned with the AIMsight board
|
|
connection pins; 6. check that the antenna connections are properly installed.
|
|
CAUTION
|
|
Use only the supplied or approved antenna and cable assembly. Changes to the antenna,
|
|
cable, connector, or mounting arrangement may reduce performance and can affect
|
|
regulatory compliance.
|
|
CAUTION
|
|
Do not install or operate the cellular antenna close to the body. The antenna is intended for
|
|
fixed or mobile installation only and must be used with a minimum separation distance of 20
|
|
cm from any person during normal operation.
|
|
|
|
Source : AIMsight Station Guide, rév. 1.5
|